The Arduino Mega Click Shield is an extension for Arduino Mega and any other boards that share its pinout. It's a simple shield with three mikroBUS™ host sockets that allow you to connect more than 1100 different types of click ...

Add colour sensing functionality to your device with the MikroE Color Click Board™. This compact accessory board employs TCS3471 colour light-to-digital converter sensor, three NPN resistor-equipped transistors, as well an RGB LED diode. With a resolution of up to 16 ...

The MPU 9DOF Click Board™ from MikroE is a measurement add-on board that includes the MPU-9150 motion tracking MikroBUS module. The Click Board™ includes two devices: a MPU-6050 3-Axios Accelerometer and 3-Axis Gyroscope and an AK8975 3-Axis Compass.

The Boost 4 Click Board™ carries the TPS61230A, high efficiency fully integrated synchronous boost converter from Texas Instruments. The Click Board™ is designed to run on a 3.3V power supply. The Boost 4 Click Board™ drives the target chip through ...

The Charger 5 Click Board™ is designed to charge Lithium-Ion and Lithium-Polymer batteries. Besides the over-voltage and under-voltage protection, reverse discharge and over-temperature protection, automatic recharge and end of charge safety timer, the Click Board™ also introduces the fast charging ...

The Buck 11 Click Board™ is a high-efficiency step-down converter that provides 3.3V on its output, derived from the connected power supply voltage, in the range from 4.2V to 60V. Buck 11 Click Board™ is based on the LMR36015, a ...

The Balancer 5 Click Board™ is an intelligent 2-cell Li-Ion battery charger, system power manager, and battery fuel gauge Click Board™. The Balancer 5 Click Board™ is based on a BQ25887 controller which has some extra features enabling charging without ...

The 6DOF IMU 3 Click Board™ is a complete 6-axis detection development board suitable for movement and position tracking devices. This Click Board™ board features the compact FXOS8700CQ motion sensor from NXP, an integrated 3-axis linear accelerometer and a 3-axis ...

The AN to PWM 2 Click Board™ is a compact add-on board that contains an easy-to-use component that converts the value of the input analogue signal to a fixed frequency PWM voltage output, with a duty cycle proportional to the ...

The Single Wire CAN Click Board™ is a compact add-on board that contains an IC for a single wire data link capable of operating with various protocols such as the Controller Area Network (CAN). This board features the NCV7356D1R2G, Single ...

The 6DOF IMU 13 Click Board™ is a compact add-on board that contains an eCompass that consists of a 3-axis linear accelerometer and a 3-axis magnetic field sensor. This board features the MC6470, an accelerometer and magnetometer for a 6 ...

The 6DOF IMU 14 Click Board™ is a compact add-on board that contains a 6-axis MEMS motion tracking device combining a 3-axis gyroscope and a 3-axis accelerometer. This board features the ICM-42688-P, high precision 6-axis MEMS motion tracking device, from ...

The DTMF Generator Click Board™ is a compact add-on board that generates DTMF (Dual-Tone Multi-Frequency) signals designed for MCU interfaces. This board features the HT9200A, a dual-tone multi-frequency decoder mostly used in mobile communications systems from Holtek Semiconductor Inc. The ...

The Tag Connect TC2050-IDC-NL-430 is a No Leg cable designed for use with the MSP430 / FET430.

The 6DOF IMU 17 Click Board™ is a compact add-on board that contains a 6-axis inertial measurement unit. This board features the IIM-42652, a 6-axis SmartIndustrial™ MotionTracking device that supports an extended operating temperature range for industrial applications from TDK ...

The Expand 10 Click Board™ is a compact add-on board that contains a multi-port I/O expander. The board features the PCAL6524, a 24-bit general-purpose I/O expander providing remote I/O expansion for most MCU’s families via the Fast-mode Plus I2C-serial interface ...