IC/Module: LM386 Audio Amplifier The AudioAMP Board is based on the LM386 power amplifier intended for low-voltage consumer applications. In order to keep external part count low, the gain is initially set to 20. However, with the addition of an ...

IC/Module: MCP1640 Synchronous Boost Regulator The Battery Boost Shield is based on the MCP1640,a compact, synchronous step-up DC-DC converter with up to 96% typical efficiency, capable of low start-up voltage and delivers high efficiency over a wide load range for ...

Breadboard Clear Self-Adhesive 830 points.

IC/Module: MCP2551 CAN Transceiver.The MCP2551 is a high-speed CAN transceiver that serves as an interface between a CAN protocol controller and the physical bus. This fault-tolerant device provides differential transmit and receive capability for the CAN protocol controller. Fully compatible ...

Character LCD 2x16 with blue backlight.

The EasyBuzz Board features a Piezo Speaker capable of emitting audio signals. For the piezo buzzer to operate normally it is necessary to generate a voltage signal of specified frequency. Piezo buzzer's resonant frequency is 3.8kHz (where you can expect ...

Now easily add LED signals to the design using the EasyLED R Board. The EasyLED R Board is a cost-effective yet effective solution for visual indication of output signals. Featuring 8 surface mounted LEDs, the EasyLED Board is used to ...

RJ45 Ethernet Connector This high-quality Ethernet connector is a standardized physical network interface commonly used for Ethernet networking. Slightly wider than a telephone jack, Ethernet cables come with an RJ45 (Registered Jack) connector on each end. The 8-position, 8-contact (8P8C) ...

FRDM-KL46Z Development Platform FRDM-KL46Z Click Board™ shield is an extension for Freescales FRDM-KL46Z development platform. Its a simple shield with two mikroBUS host sockets that allow you to interface more than 100 different types of Click Board™s with the Kinetis ...

The GLCD 240x128 Adapter Board is used to connect a 240x128 GLCD with T6963C Toshiba driver to your development board or prototype device. Board features a potentiometer used for GLCD contrast adjustment. It is equipped with two long flat cables, ...

GSM Antenna SMA straight male (Cable length: 2m).

IPEX-SMA cable. Fore use with MikroElektronika GSM/GPRS boards.

The Keypad 4x4 Board features 16 push buttons arranged in 4x4 matrix to form standard alphanumeric keypad. Some embedded systems that require user input in form of numbers (decimal, or hexadecimal) can use this board as a solution. Board features ...

IC/Module: MAX232N Dual EIA-232 Drivers/Receivers The integrated MAX232N is a dual EIA-232 driver/receiver that operates from a single 5-V power supply and converts a serial signal from TTL to RS232C standard and vice versa through a built-in voltage generator. The ...

UART Interface The MAX3232 Board sends/receives data to/from the host microcontroller using serial UART communication. The data is first converted as per the RS232 standard, and then sent to the RS232 device. Two Connectors The MAX3232 Board features two connectors: ...

The mikroBUS Cape is an extension for Beagle™one Black, the popular low-cost development platform running Linux. This simple cape has four mikroBUS sockets that allow you to connect more than 130 different types of Click Board™s to Beagle™one. Quickly add ...

mikroBUS Host Connector Each mikroBUS host connector consists of two 1x8 female headers containing pins that are most likely to be used in the target accessory board. The mikroBUS host connector perfectly fits into standard breadboards. Prototyping Area The board ...

The Flash Click Board™ contains 8,388,608 bits (8 Mbit) of Flash memory organized into 1,048,576 bytes (1 MB). In other words, the Flash Click Board™ is a flash memory medium with the capacity of 1 MB. The used flash module ...