Non-printed Hardware needed to build an OpenAstroGuider v3.1 Version 3.1 requires the use of the custom PCB and a USB C cable. You need the PCB regardless if you are using the dew heater or not! You can build v3.0 ...

Build it yourself! The DIY Kit includes everything you need to build your own OpenAstroTracker and get started in Astrophotography! You will need your own camera though. The OpenAstroGuider is not included! Check it out and take your exposures to ...

This RA Ring for the OpenAstroTracker is printed in a single piece and has the middle part reinforced. This reduces the error caused by joining the ring from several pieces and will increase the consistency of Polar alignment. Please use ...

Struggle to get the tolerances right for the OpenAstroGuider? These parts here have as perfect tolerances as its probably possible. The focus thread comes pre-applied with lubricant and mounting parts for the aluminum extrusion are included. The material is quality ...

OpenAstroGuider: Your Affordable Autoguider for Stunning Astrophotography Unlock the cosmos without breaking the bank with the OpenAstroGuider. Designed for both amateur and seasoned astrophotographers, this budget-friendly autoguider is your gateway to capturing the night sky in stunning detail. Built-In Camera ...

All mechanical printed parts to build an OpenAstroTracker. The RA Ring is NOT included! The two moving DEC parts have their 6001 bearings press-fit into them and are included. A bubble level is also included. Printed from quality PLA made ...

A pre-crimped 10 pin ribbon cable to connect a LCD shield to the MKS's EXP1 port. Comes with a 10-pin Dupont cable attached so you just have to connect the LCD. Check this page for instructions. Length: roughly 40cm

A standard LCD shield suitable for Arduino Mega or MKS (with the ribbon cable)

Complete Kit of all the non-printed parts to build an OpenAstroTracker. If you need Threaded Inserts for the _TI version of the printed parts, add them here. Includes: Electronics: 2x NEMA17 1x MKS Gen L 2.1 2x Bigtreetech TMC2209 1.2 ...

All screws and nuts for assembling an OpenAstroMount. Screws are either 8.8/10.9 zink plated or A2 stainless. 4x M3x6 30x M3x10 100x M3x12 200x M4x12 12x M5x12 8x M5x20 6x M5x30 2x M5x20 FH 32x M5/M6x20 FH 2x M5/M6x40 thumbscrew ...

60 M3x4.6x6mm Inserts for OAT. At this point this product can only be purchased in combination with other items!

Contains all the Hardware needed to build an OpenAstroExplorer. 65 Printed Parts and 300 hardware parts and screws! The printed parts come with the heated inserts already pressed in. To assemble you will need a set of Hex Keys. Additionally ...

All Extrusion are drilled and tapped, ready to use. 1x 2020 300mm 1x 2020 200mm 1x 2020 50mm 1x 4040 75mm

Contains: Motion Kit Electronics Kit & PCB Screw Kit Stepper Kit Extrusion Kit Bearing Kit Clamp Kit

All bearings for the OpenAstroExplorer 2x 6012 ZZ 7x 625 ZZ ABEC5 4x F695 ZZ 2x 6907 1x F6006 1x 51111 1x LM5UU

All Motion components for the OpenAstroExplorer 4x GT2 16T Pulley 2x GT2 48T Pulley 3x GT2 looped belts 1x Worm gear set 1x MGN9C linear rail 2x Shaft couplers 40cm GT2 belt

All Arcaswiss clamps and plates used for the OpenAstroExplorer. 1x 120mm Clamp & Plate set 1x 90mm Clamp 1x 200mm Plate

Electronic components for the OpenAstroExplorer. If you need all electronics, you have to purchase all 3 options! PCB: PCB only Electronics: 1x ESP32 2x TMC2209 2x A4988 1x DC Barrel 2x Connector Cable NEMA17 Steppers (come crimped with proper connector) ...

Contains all small parts as described in the OpenAstroExplorer BOM

I am unclear whether or not I will actually offer a pre-built OpenAstroExplorer. Leave your Email in the "Notify me when available" form if you would buy one, so i can gauge the interest in this. Thanks!