Ideal for following templates, routing sign lettering and other tasks where the pattern is placed on top of the work piece. The top mounted bearings on these bits make them ideal for almost any application where the work piece is ...

Mortise Compression Spiral Bits feature a shorter up shear length than other compression spiral bits, making them ideal for grooves and mortises, or for through-cuts in thin double sided material (5/8" thick or less). Rout plywood, melamine and other double-sided ...

Freud's huge selection of carbide tipped and solid carbide double flute straight bits are ideal for grooving, edge-routing and other general purpose routing tasks. The precise hook and shear angles provide fast cutting and a smooth finish in hardwood, softwood, ...

Half Round Bits produce a fully rounded semicircular edge on dimensional lumber. In a single operation they create an attractive half-round profile that is ideal for stair treads, furniture and moldings. Must be used with a router table fence or ...

"V" Grooving bits are the perfect choice for making signs, engraving wood plaques, adding decorative accents to furniture or adding visual interest to millwork. Use these versatile bits in hand-held, table-mounted or CNC routers to rout hardwood, softwood, plywood, plastics ...

Oneway 1”-8 TPI from 3/4"-10 TPI Live Centre Adaptor

This clever bit is designed to hang pictures, plaques or even shelves with completely concealed fasteners. The large diameter end bores holes to allow nail or screw heads to enter the slot, and the smaller diameter allows room for the ...

Down spiral bits are a great choice for grooves and dadoes in single-sided veneers and laminates where chip removal is not a problem, or for through-cuts where finish quality on the top surface is the primary consideration. Also cuts well ...

A combination of up and down shear flutes allow these bits to produce clean, chip-free top and bottom surfaces in double-sided veneers or laminates. The single-flute design is ideal for fast routing in almost any material, including hardwood, softwood, plywood ...

7.5° x 3/16" Engraving V-Groove Solid Carbide Bit. 1/2" Cutting Length. 1/4" Shank. Perfect for engraving and lettering applications in hard or soft wood, or composite materials. Ideal for Wood, Wood Composites, Plastics (Hard & Soft), and Aluminum for 2D ...

Clamp Block 2 1/2" Bed Gap for Powermatic 3520, Vicmarc VL300/VL175 Lathe for Oneway Bowl Steady, Spindle Steady or Coring System Extra clamp blocks for use in the Easy-Coring Systems, Bowl Steady, and, Spindle Steady.

The Flexcut SlipStrop is an economical way for maintaining our tools razor edge. It has been specially molded to allow for polishing and deburring the hard-to-reach areas on the inside of V-tools and gouges as well as the outside edge ...

Scorps are essentially right-angled gouges designed for carving areas where the full length of a gouge will not fit. Knife carvers will find them useful for hollowing deep, narrow cavities. Right and left-handed models are available. Right-Handed carvers should choose ...

These jaws are aluminum plates machined from a solid (for greater strength). Their unique combination of slots and tapped holes for mounting the rubber grippers allows holding an infinite number of round, oval or square shapes. The buttons are hard ...

Suitable for use on the Mini Grinder Tungsten carbide teeth 10mm (3/8″) depth of cut 4mm (5/32″) width of kerf Easily resharpened using a fine diamond EZE Lap file This purchase includes: 1 x Mini Industrial Blade 1 x Brass ...

Satin Finishing Wax 8oz is a special blend of waxes designed to give oil-finished woods a rich luster. It can be used as a polish for rubbing out new finishes or as a scratch-remover for worn surfaces. It works well ...

Cutting width 0.070" (1.8 mm) Diameter 6.29" (160 mm) Hole dia. 4/5" (20 mm) 28 TPI

11" Maroon Very Fine Finishing Pad

11" Gray Ultra Fine Finishing Pad